Stereo Digital Camera Hop System
18" Dual XLRM to 3.5mm M2R Output Cable
The DCHT transmitter is designed for use in film and television production to provide a wireless link from a bag or cart system to cameras and recorders. The transmitter will accept mic or line level analog signals or AES digital signals from a mixer and transmit the signals to the receiver in a pure digital format.
The digital architecture is a third generation design with specially developed, high efficiency digital circuitry for extended operating time on two AA batteries. The transmitter can tune in coarse or fine steps across the UHF television band from 470.100 to 607.950 MHz, with a selectable output power of 10, 25 or 50 mW.
The pure digital architecture enables AES 256-CTR encryption for high level security applications.
Studio quality, stereo audio performance is assured by high quality components in the preamp, wide range input gain adjustment and DSP-controlled limiting. Input connections and settings are included for any lavaliere microphone, dynamic microphones and line level inputs. Input gain is adjustable over a 51 dB range in 1 dB steps to allow an exact match to the input signal level, maximizing the dynamic range and signal to noise ratio.
The top panel contains the antenna jack, two audio input level LEDs (one per audio channel), the programmable function switch and the audio input jack. The red/green LEDs provide audio level indications from -20 dB to the onset of limiting for each channel for accurate input gain adjustment. The programmable switch can be configured as a mute switch, a power on/off switch, or be bypassed. The 6-pin input jack accepts two mic or line level analog signals or AES digital signals from external sources via a variety of adapter cables. Analog inputs can be linked for the same gain when used with a stereo source, or operate independently with individual settings.
The housing is constructed of solid machined aluminum for lasting ruggedness. The exterior is finished with an ultra hard, dark electroless nickel finish.
The transmitter is supplied with a stainless, spring wire belt clip that is secure, but easily detached and re-attached without tools. A spring-loaded belt clip is available as an option. The battery door is machined aluminum,
hinged to the housing to prevent it being lost. The battery door latches securely to prevent being opened inadvertently, and will not pop open even if the unit is dropped.
Firmware updates are made via the USB port on the side panel of the housing. The procedure is very simple using a menu item on the transmitter and a standard micro USB cable.
Setup and adjustment is enabled through a backlit LCD, membrane switches and an intuitive menu structure. Input gain is adjustable over a wide range in 1 dB steps to optimize modulation and limiting for maximum signal to noise ratio and minimum distortion.
The M2R Digital Receiver employs advanced antenna diversity switching during digital packet headers for seamless audio. The receiver covers the UHF frequencies of 470-608 MHz in a single range and uses digital modulation. The 24-bit digital audio stream guarantees high resolution sound quality with wide dynamic range, low noise oor, and solid stereo image.
The headphone jack is fed from a high-quality stereo ampli er with 250 mW available to drive headphones or earphones to suf cient levels for stage performance or other noisy environments. The receiver can select from stereo, mono from left channel only, or mono from right channel only, giving the unit exibility in terms of the application. An intuitive mixing interface and high resolution, color LCD on the belt pack receiver provide performing artists and monitor engineers alike with a comfortable and con dent user experience.
Optional Battery Eliminator
Both the transmitter and receiver can be powered by external DC using the optional LTBATELIM power supply adapter. The battery door is replaced by the adapter with a simple procedure. The adapter provides a locking coaxial connector and a variety of power cords and connectors are available.
Accessory Input Cable Adapters
MCTA6TA5M2 -- adapter for two lav mics or line level signals via two TA5M connectors to TA6F
MCTA6TA3F2 -- adapter for two line level signals via two TA3F connectors to TA6F
MCTA6XLRF2 -- adapter for two line level signals via two XLRF connectors to TA6F
MCTA6AESXLRF -- adapter for one dual-channel AES digital signal via one XLRF to TA6F
MCTA6PT -- adapter for two mic or line level analog signals via two pigtail lines to TA6F